{"id":19462,"date":"2026-08-01T18:01:07","date_gmt":"2026-08-01T10:01:07","guid":{"rendered":"https:\/\/daxuns.com\/?p=19462"},"modified":"2026-08-03T10:46:10","modified_gmt":"2026-08-03T02:46:10","slug":"caustic-soda-evaporator-materials","status":"publish","type":"post","link":"https:\/\/daxuns.com\/id\/caustic-soda-evaporator-materials\/","title":{"rendered":"Nickel 200\/201 vs Alloy 600 for Caustic Soda Evaporators"},"content":{"rendered":"\n
<\/span>\"Multi-effect
\n\n

Nickel 200 | Nickel 201 | Alloy 600<\/p>\n\n\n

Select caustic evaporator materials by equipment zone, wall temperature, contaminants, and stress<\/strong><\/p>\n\n\n

A component-level material decision for bodies, heating tubes, coils, tube sheets, and vapor-side equipment.<\/p>\n\n<\/div><\/div>\n\n\n\n

\n\n

Direct answer:<\/strong> Nickel 200 and Nickel 201 are usually the first nickel materials to evaluate for hot, concentrated caustic soda because commercially pure nickel develops a protective oxide film and has very low corrosion rates in many sodium-hydroxide environments. Nickel 201 is preferred when metal temperature can exceed approximately 315 C because its lower carbon content reduces the graphitization risk associated with prolonged high-temperature exposure. Alloy 600 becomes attractive when the design needs greater strength, heating-coil performance, or improved tolerance of certain sulfur-bearing contaminants, but severe hot caustic can cause stress-corrosion cracking if stress and metallurgical condition are not controlled.[1][2][3]<\/p>\n\n<\/div><\/div>\n\n\n\n

\n
\n\n

FIRST CORROSION SCREEN<\/p>\n\n\n

Nickel 200 or Nickel 201 for many hot concentrated caustic conditions<\/strong><\/p>\n\n<\/div>\n\n\n

\n\n

HIGH-TEMPERATURE DISTINCTION<\/p>\n\n\n

Nickel 201 where graphitization risk makes low carbon essential<\/strong><\/p>\n\n<\/div>\n\n\n

\n\n

CONDITIONAL ALTERNATIVE<\/p>\n\n\n

Alloy 600 when strength, heating duty, or specific contaminants justify it<\/strong><\/p>\n\n<\/div>\n<\/div>\n\n\n\n

DAXUN manufactures Nickel 200, Nickel 201, and Alloy 600 sheet, plate, pipe, and tube for project-defined caustic soda equipment. The correct material is selected by equipment zone and exposure, not by assigning one alloy to an entire evaporator train.<\/p>\n\n\n\n

Why a Caustic Soda Evaporator Needs Zone-by-Zone Material Selection<\/h2>\n\n\n\n

Membrane-cell caustic is commonly produced at approximately 33% concentration and then evaporated to a commercial 50% solution. Diaphragm-cell liquor can enter evaporation at a lower concentration.[4] Higher concentration, rising boiling point, local film temperature, contaminants, and residual stress change the corrosion problem as liquor moves through the system.<\/p>\n\n\n\n

The material-selection chain is:<\/p>\n\n\n\n

concentration and boiling regime -> metal temperature and impurity activity -> general corrosion, graphitization, embrittlement, or cracking mechanism -> alloy, condition, fabrication, and inspection plan<\/strong><\/p>\n\n\n\n

That is why "50% NaOH" is not enough information. The same nominal concentration may contact a low-stress vessel wall, a hotter tube wall, a steam-heated surface, a stagnant crevice, or a weld with high residual stress. Those locations do not have the same risk.<\/p>\n\n\n\n

Practical Selection Summary<\/h2>\n\n\n\n
\n\n\n\n\n\n\n\n\n
Service question<\/th>\nMaterial direction<\/th>\nEngineering limitation<\/th>\n<\/tr>\n<\/thead>\n
Is high caustic corrosion resistance the primary requirement below about 315 C?<\/td>\nStart with Nickel 200 or Nickel 201<\/td>\nConfirm concentration, actual metal temperature, chlorates, sulfur compounds, and weld condition<\/td>\n<\/tr>\n
Can metal temperature exceed about 315 C for sustained periods?<\/td>\nPrefer low-carbon Nickel 201 over Nickel 200<\/td>\nThe boundary addresses graphitization risk; it is not a universal design-temperature rating<\/td>\n<\/tr>\n
Does a heating coil or pressure boundary require higher strength than commercially pure nickel?<\/td>\nEvaluate Alloy 600<\/td>\nHot concentrated caustic SCC, residual stress, and heat treatment still require qualification<\/td>\n<\/tr>\n
Are oxidizable sulfur compounds present at elevated temperature?<\/td>\nAlloy 600 may be favored over Nickel 201<\/td>\nSulfur chemistry and temperature must be quantified; generic "sulfur present" is inadequate<\/td>\n<\/tr>\n
Are chlorates or other oxidizing contaminants present?<\/td>\nDo not rely on a clean-caustic corrosion chart<\/td>\nUse representative corrosion testing or documented service evidence<\/td>\n<\/tr>\n
Is the equipment a multi-effect evaporator?<\/td>\nSelect by effect, surface temperature, and component function<\/td>\nOne material for every effect can add cost or leave the hottest zone underqualified<\/td>\n<\/tr>\n<\/tbody><\/table><\/figure>\n\n\n\n

This table is a screening tool, not a material-selection standard. Final selection belongs to the responsible equipment and corrosion engineers.<\/p>\n\n\n\n

Nickel 200 and Nickel 201 in Caustic Soda Service<\/h2>\n\n\n\n

Nickel 200 (UNS N02200) and Nickel 201 (UNS N02201) are commercially pure wrought nickel grades. Their principal procurement difference for high-temperature service is carbon control: Nickel 201 is the lower-carbon grade.[2]<\/p>\n\n\n\n

The Nickel Institute reports that Nickel 200 and Nickel 201 are generally the most corrosion-resistant commercial materials across broad caustic soda conditions. In compiled guide data, corrosion rates through approximately 73% caustic are generally below 0.025 mm\/year (1 mpy), with rates increasing somewhat above that concentration.[1] This is a useful selection reference, not a guaranteed design allowance. Source data include particular specimens, exposure histories, impurity levels, velocities, and test methods.<\/p>\n\n\n\n

Special Metals publishes one laboratory example for Nickel 200 in 50% caustic soda at 150 C: 0.010 mm\/year after a 336-hour exposure.[2] The value demonstrates why pure nickel is considered for concentrated caustic, but it must not be copied into a corrosion allowance without confirming that the project chemistry and heat-transfer conditions are comparable.<\/p>\n\n\n\n

Why Nickel 201 Is Preferred at Higher Temperature<\/h3>\n\n\n\n

Nickel 200 is normally limited to service below approximately 315 C where prolonged exposure could otherwise allow carbon to precipitate as graphite and reduce ductility. Nickel 201 was developed with lower carbon for resistance to this graphitization mechanism.[2]<\/p>\n\n\n\n

The resulting decision is not "Nickel 201 is always better." Below the graphitization range, both grades can be technically appropriate. Above it, Nickel 201 removes a material risk that Nickel 200 cannot address merely through thicker wall.<\/p>\n\n\n\n

When Alloy 600 Is the Better Candidate<\/h2>\n\n\n\n

Alloy 600 (UNS N06600) contains at least 72% nickel plus cobalt, 14-17% chromium, and 6-10% iron in the producer-published composition.[3] Compared with commercially pure nickel, it offers higher strength and retains useful properties at elevated temperature.<\/p>\n\n\n\n

The Nickel Institute describes Alloy 600 as having caustic corrosion resistance similar to commercially pure nickel through anhydrous caustic in many conditions. It is used for heating coils and other components where higher-temperature strength matters. The same guide also identifies sulfur-bearing caustic as a case where Alloy 600 may be preferred because it is less susceptible than commercially pure nickel to a low-melting nickel-sulfide reaction.[1]<\/p>\n\n\n\n

Those advantages do not make Alloy 600 immune to caustic cracking. Producer guidance warns that high-strength caustic at elevated temperature can cause stress-corrosion cracking, particularly when high residual or operating stress is present. Stress-relief examples are published for specific conditions, but the project must approve the actual cycle because heat treatment also affects grain size, dimensions, surface, and mechanical response.[3]<\/p>\n\n\n\n

Use Alloy 600 because a defined requirement justifies it, such as:<\/p>\n\n\n\n