2205 vs 2507 Duplex Stainless Steel Pipe: PREN, Standards, and Choosing Between Them<\/h1>\n
Pendahuluan<\/h2>\n
The choice between 2205 and 2507 duplex stainless steel usually isn’t about strength. Both are roughly twice as strong as 316L, both resist chloride stress corrosion cracking far better than austenitic grades, and in most product forms both will pass their acceptance tests without complaint. The real question is narrower: how aggressive is the chloride environment, and are you paying for corrosion margin you don’t actually need?<\/p>\n
2507 costs noticeably more than 2205 \u2014 higher chromium, higher nickel, higher molybdenum, higher nitrogen. In warm chlorinated seawater it earns that premium. In a moderately chlorinated chemical line at 60 \u00b0C, it often doesn’t.<\/p>\n
This page covers the grade comparison that applies to any product form \u2014 composition, mechanical properties, PREN, and the selection logic \u2014 and then goes deeper on pipe, because pipe is where specification mistakes get expensive. Three different ASTM standards cover duplex pipe depending on how it was made, and buyers mix them up regularly. If you’re specifying plate, bar, or coil instead, the grade-level sections below apply equally; the standards and fabrication sections are pipe-specific.<\/p>\n
One thing worth flagging up front: if your drawing says “2205,” it may not be specific enough. More on that below.<\/p>\n
<\/p>\n
What Separates 2205 from 2507?<\/h2>\n
Both are duplex stainless steels \u2014 roughly balanced ferrite and austenite microstructures, which is where the strength and the chloride SCC resistance come from. The difference is alloy content, and the practical shorthand for that difference is PREN (Pitting Resistance Equivalent Number):<\/p>\n
2205<\/strong> \u2014 about 22% Cr, 3% Mo, 5\u20136% Ni, nitrogen-alloyed. Typical PREN lands around 34\u201336, which puts it in the standard duplex class.<\/li>\n
2507<\/strong> \u2014 about 25% Cr, 4% Mo, 7% Ni, higher nitrogen. Typical PREN lands around 41\u201343, crossing the PREN \u2265 40 threshold that defines super duplex.<\/li>\n<\/ul>\n
PREN is a comparison index, not a design value. It ranks grades against each other for pitting resistance; it does not tell you the critical pitting temperature in your specific medium, and it says nothing about crevice corrosion at a gasket face or under a deposit. Treat it as a first screen, then verify against test data or corrosion-engineering input for the actual service condition.<\/p>\n
<\/p>\n
The S32205 vs S31803 trap<\/h3>\n
“2205” maps to two different UNS numbers, and they are not equivalent:<\/p>\n
\n
UNS S32205<\/strong> \u2014 the modern, tightened version: higher nitrogen minimum (0.14%), narrower chromium and molybdenum bands.<\/li>\n
UNS S31803<\/strong> \u2014 the original, wider grade: nitrogen minimum as low as 0.08%, wider Cr and Mo ranges.<\/li>\n<\/ul>\n
A heat can meet S31803 and still sit at the low end of nitrogen and molybdenum, which drops the PREN and hurts weldability \u2014 nitrogen is what stabilizes austenite reformation in the heat-affected zone. Many mills dual-certify to both, which is fine, but a purchase order that just says “2205” leaves the door open to material at the bottom of the S31803 range. If you want the modern chemistry, write S32205 on the PO.<\/strong> This one line has caused more duplex disappointment than any exotic corrosion mechanism.<\/p>\n
2205 vs 2507 \u2014 Quick Comparison<\/h3>\n
\n\n
\n
<\/th>\n
2205<\/th>\n
2507<\/th>\n<\/tr>\n<\/thead>\n
\n
\n
UNS number<\/td>\n
S32205 (modern) \/ S31803 (older, wider)<\/td>\n
S32750<\/td>\n<\/tr>\n
\n
EN designation<\/td>\n
1.4462<\/td>\n
1.4410<\/td>\n<\/tr>\n
\n
Nominal chemistry<\/td>\n
22Cr-5Ni-3Mo-N<\/td>\n
25Cr-7Ni-4Mo-N<\/td>\n<\/tr>\n
\n
Typical PREN<\/td>\n
~34\u201336 (standard duplex)<\/td>\n
~41\u201343 (super duplex)<\/td>\n<\/tr>\n
\n
Class<\/td>\n
Dupleks<\/td>\n
Super duplex<\/td>\n<\/tr>\n
\n
Relative strength<\/td>\n
High (roughly 2\u00d7 316L yield)<\/td>\n
Higher still<\/td>\n<\/tr>\n
\n
Typical use envelope<\/td>\n
Moderate to high chloride, general corrosive service<\/td>\n
Warm\/chlorinated seawater, high-chloride and acidic-chloride service<\/td>\n<\/tr>\n
\n
Relative cost<\/td>\n
Lower<\/td>\n
Lebih tinggi<\/td>\n<\/tr>\n
\n
Fabrication sensitivity<\/td>\n
Requires heat-input control<\/td>\n
Requires tighter heat-input control and a narrower processing window<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
This table ranks the two grades against each other; it is not a substitute for a corrosion assessment of your medium, temperature, and chloride level.<\/p>\n
Key Specifications<\/h2>\n
\n
Nilai<\/strong>: 2205 (UNS S32205 \/ S31803, EN 1.4462) and 2507 (UNS S32750, EN 1.4410)<\/li>\n
Governing pipe specifications<\/strong>: ASTM\/ASME A790 (seamless and straight-seam \u2014 that is, longitudinally \u2014 welded, no filler metal added), ASTM A928 (electric-fusion-welded with filler metal added), ASTM A789 for tubing rather than pipe<\/li>\n
Manufacturing route<\/strong>: Seamless or welded, as ordered \u2014 the route determines which specification applies<\/li>\n
Delivery condition<\/strong>: Solution annealed and rapidly quenched. This is not optional for duplex; it is what dissolves intermetallic phases and restores the phase balance<\/li>\n
Size range<\/strong>: Commonly NPS 1\/2″ through 24″, with schedules to ASME B36.19M (5S \/ 10S \/ 40S \/ 80S the usual stock range); larger and heavier walls by arrangement<\/li>\n
Ends<\/strong>: Plain end or bevelled end; threaded as ordered<\/li>\n
Documentation<\/strong>: Mill test certificate with heat and lot traceability; EN 10204 3.1 inspection document where the buyer’s quality system calls for it<\/li>\n
Temperature limit<\/strong>: Duplex grades are not intended for prolonged service above roughly 300 \u00b0C because of embrittlement \u2014 see the fabrication section below<\/li>\n<\/ul>\n
Size availability, wall thickness, and testing scope should be confirmed against current mill capability, since not every grade and schedule combination is stocked in both 2205 and 2507.<\/p>\n
Chemical Composition<\/h2>\n
\n\n
\n
Element (wt.%)<\/th>\n
2205 (S32205)<\/th>\n
2507 (S32750)<\/th>\n<\/tr>\n<\/thead>\n
\n
\n
Karbon (C)<\/td>\n
\u22640.030<\/td>\n
\u22640.030<\/td>\n<\/tr>\n
\n
Kromium (Cr)<\/td>\n
22.0 \u2013 23.0<\/td>\n
24.0 \u2013 26.0<\/td>\n<\/tr>\n
\n
Nikel (Ni)<\/td>\n
4.5 \u2013 6.5<\/td>\n
6.0 \u2013 8.0<\/td>\n<\/tr>\n
\n
Molibdenum (Mo)<\/td>\n
3.0 \u2013 3.5<\/td>\n
3.0 \u2013 5.0 (typically around 4.0)<\/td>\n<\/tr>\n
These are the commonly published composition ranges for the two grades. The applicable specification and its currently active edition control acceptance \u2014 ASTM revises tubular-product specifications periodically, so the edition should be stated on the purchase order rather than assumed. Two further notes: S31803 (the older “2205”) carries wider Cr, Mo, and N ranges than shown here for S32205; and the nitrogen band above is the ASTM range for S32750 \u2014 EN 1.4410 permits a wider range, so a heat certified to EN may sit outside these limits while still being compliant to its own standard.<\/p>\n
Typically limited to around 32 HRC<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
Reference values for solution-annealed pipe, shown for comparison \u2014 not guaranteed acceptance values. Actual acceptance depends on the governing specification and edition, product form, wall thickness, and manufacturing route. Two details worth noting: older S31803 material carries a lower tensile minimum than S32205, and 2507’s higher strength comes with lower minimum elongation, which matters if the line involves field bending or cold forming.<\/p>\n
<\/p>\n
Product Forms Available<\/h2>\n
Pipe and tube:<\/p>\n
\n
Seamless pipe<\/li>\n
Welded pipe (straight-seam, no filler metal \u2014 A790 route)<\/li>\n
Electric-fusion-welded pipe (filler metal added \u2014 A928 route)<\/li>\n
Tubing for heat exchangers and condensers (A789 route)<\/li>\n